A Hoover WindTunnel vacuum does a great job of sucking up dirt and debris, a task that makes it filthy over time. For the appliance to continue doing a clean job, it needs regular maintenance. This includes washing the necessary parts, emptying the canister, and checking that the moving parts are in good condition.

How to clean Hoover WindTunnel Canister: Start by removing the Hoover WindTunnel canister from the cleaner. Next, hold the Hoover canister over a trash can and press the release lever to empty the dirt, dust, and mess inside the canister. Finish by wiping the inside of the canister with a dry cloth.

With that being said, the cleaning procedure may vary from one model to another. This is a specific guide on how to clean a Hoover WindTunnel canister model. In addition to cleaning the canister properly, you must know how to disassemble and reassemble it into a working condition as well. Let’s get started.

How to Clean Hoover WindTunnel Canister:

A Hoover WindTunnel vacuum cleaner needs enough airflow to work effectively. Because of this, it’s important to keep the filters and canister clean. As a general rule of thumb, you will need to empty the vacuum’s canister whenever it’s halfway full. Here are the tools you need to start cleaning:

1. Running Water
2. Microfiber Cloth 
3. Scissors
4. Grout Brush

Additionally, it’s better to perform the cleaning process on a sink with running water. If you are short on time and prefer the video version of this tutorial, watch the helpful videos below. However, if you would like to read the comprehensive step-by-step post on how to clean a Hoover WindTunnel canister, read the article below. 

Remember, the very first thing you must do before attempting to clean your Hoover WindTunnel canister is to ensure it’s unplugged. Make sure to both turn the power off and unplug the power cord. Failure to do so may put you at risk of an electrical hazard if anything goes wrong with the power outlet.

Step 1: Cleaning the Filters

Cleaning your filters will help keep your Hoover vacuum running at its peak performance. There are two filters. The primary filter should be cleaned every two months or as needed. And the HEPA filters should be cleaned every six months for optimal performance. To get started, put the cleaner in an upright position.

1. Clean the Primary Filter

To clean the primary filter, remove the dirt cup from the cleaner and flip the lid open. Then, remove the rinsable filter and rinse with water for approximately two minutes, or until the water runs clear. Squeeze out the excess water and allow to dry for at least 24 hours. Never put a wet rinsable cleaner back into the cleaner.

2. Replace the HEPA Filter

The second filter is located in the bottom part of the canister, where it says ‘HEPA’. To clean it, put your hand on the latch and slide it out. Do not wash the HEPA filter with water. Simply tap the filter against the inside of a trash can to remove the dirt and debris. Replace the filter and make sure you hear it snap into place.

PRO TIP: To ensure proper functioning of your Hoover WIndTunnel vacuum, be sure to only replace the filters with authorized Hoover parts. Failure to do so may cause malfunction of the unit. Thankfully, you can easily buy anything you need, including parts and accessories, from Hoover’s Official Amazon store.

Step 2: Cleaning the Canister (Dirt Cup)

1. Simple Cleaning

When it comes to cleaning the canister, we recommend emptying it regularly. Be sure to empty it before the dirt reaches the MAX line. To empty it, put the cleaner into the upright position. Turn the power off, release the dirt cup from the cleaner by pressing the release button, and carry it to a trash can.

Hold it over a trash can, and press the release lever or button firmly located on the back of the cup. The dirt, dust, and mess will spill automatically into the trash. Close the bottom to snap shut, and replace the canister by putting the bottom edge in first, then pivoting it back to snap it into place.

2. Thorough Cleaning

If you wish to clean your canister more thoroughly, you can clean the upper portion as well. After emptying the contents, you can lift the filter assembly from the canister by turning it counterclockwise, and clean it with a dusting brush or a soft cloth. The entire filter assembly should come out as one piece.

Before submerging any part of the Hoover canister in water, check the manual to see if it’s safe to do so. Depending on the model, some should only be cleaned using dry cloth only. Thankfully, both the filter assembly and the inside of the canister can be easily wiped clean with a soft, dry cloth.

Once you have wiped off the filter assembly and the inside of the canister, put the filter assembly back into the canister, and turn the handle clockwise until it locks firmly into place. To replace the Hoover canister, set the bottom edge in first and pivot the top until it clicks into the locked position.

Hoover WindTunnel Maintenance Tips

It’s essential to observe some maintenance tips in addition to cleaning a Hoover WindTunnel vacuum cleaner. Check that you've done the following:

• Replace the bag regularly if your unit comes with one and ensure it is attached properly
• Empty the bagless vacuum cleaner as often as possible
• Clean the brush roll to remove pet hair that prevents it from spinning correctly
• Check that the belt is in the right position
• Ensure the filters and hoses are clean and replaced periodically

If you notice any problem with your vacuum cleaner, we recommend seeking professional help. Don't attempt to fix it yourself. Take it to the vacuum shop for professional assistance. A professional vacuum cleaner expert should be able to diagnose the problem and find the best solution for your beloved cleaning tool.

Final Thoughts

A Hoover WindTunnel vacuum cleaner, just like any other machine, requires regular cleaning and maintenance. This is the only way to keep it working efficiently and improve its lifespan. Take extra care when cleaning the parts, ensuring you first remove them from their respective positions before treating the unit.

Replace the parts that need replacing with authorized accessories and ensure everything is in good working condition. Don’t hesitate to get professional help if the need arises. Alternatively, buy a new upright vacuum cleaner if you need one. Hopefully, this has helped you learn how to clean Hoover WindTunnel canister.